{"product_id":"i̇zotup-200-enjeksiyon-kiti","title":"Izotope 200-E Injection Kit (350dm³)","description":"\u003cp data-path-to-node=\"7\"\u003e\u003cb data-path-to-node=\"7\" data-index-in-node=\"0\"\u003eProfessional solution for small to medium-sized voids.\u003c\/b\u003e\u003c\/p\u003e\n\u003cp data-path-to-node=\"7\"\u003eIzotüp 200-E is a 2-component, portable injection system designed to fill hard-to-reach voids, double-walled structures, and small cracks.\u003c\/p\u003e\n\u003cul\u003e\n\n\u003cli\u003e\n\n\u003cb data-path-to-node=\"8,0,0\" data-index-in-node=\"0\"\u003eFilling Capacity:\u003c\/b\u003e A single kit fills approximately \u003cb data-path-to-node=\"8,0,0\" data-index-in-node=\"43\"\u003e350 \u003cspan class=\"math-inline\" data-math=\"dm^3\" data-index-in-node=\"47\"\u003edm³ \/ 0.3m³\u003c\/span\u003e\u003c\/b\u003e of volume.\u003c\/li\u003e\n\n\u003cli\u003e\n\n\u003cb data-path-to-node=\"8,1,0\" data-index-in-node=\"0\"\u003eAreas of Use:\u003c\/b\u003e Ship and boat bilge fillings, door and window frames, cold room panels, and small-scale structural voids.\u003c\/li\u003e\n\n\u003cli\u003e\n\n\u003cb data-path-to-node=\"8,2,0\" data-index-in-node=\"0\"\u003eHigh Insulation:\u003c\/b\u003e Provides maximum thermal protection with an R-6.2 value.\u003c\/li\u003e\n\n\u003cli\u003e\n\n\u003cb data-path-to-node=\"8,3,0\" data-index-in-node=\"0\"\u003eAdvantage:\u003c\/b\u003e Requires no electrical or machinery investment; immediate filling with a plug-and-play system.\u003c\/li\u003e\n\n\n\u003c\/ul\u003e\n\u003ch3 data-path-to-node=\"5\"\u003e1. Gun and Nozzle Preparation\u003c\/h3\u003e\n\u003cul\u003e\n\n\u003cli\u003e\n\n\u003cb data-index-in-node=\"0\" data-path-to-node=\"6,0,0\"\u003eUse of Petroleum Jelly:\u003c\/b\u003e Before attaching the nozzle, apply a thin layer of \u003cb data-index-in-node=\"78\" data-path-to-node=\"6,0,0\"\u003epetroleum jelly\u003c\/b\u003e to the tip of the gun. This prevents hardened foam from damaging the gun.\u003c\/li\u003e\n\n\u003cli\u003e\n\n\u003cb data-index-in-node=\"0\" data-path-to-node=\"6,1,0\"\u003eFull Locking:\u003c\/b\u003e When attaching the nozzle to the gun, ensure it is \u003cb data-index-in-node=\"41\" data-path-to-node=\"6,1,0\"\u003efully seated and locked\u003c\/b\u003e. If the nozzle is not fully seated, the material may back up into the gun, rendering the equipment unusable.\u003c\/li\u003e\n\n\n\u003c\/ul\u003e\n\u003ch3 data-path-to-node=\"7\"\u003e2. Initial Start-up (Test Spray)\u003c\/h3\u003e\n\u003cul\u003e\n\n\u003cli\u003eBefore proceeding with the injection, perform a \u003cb data-index-in-node=\"81\" data-path-to-node=\"8,0,0\"\u003esmall test spray\u003c\/b\u003e into the product box or an empty waste container.\u003c\/li\u003e\n\n\u003cli\u003e\n\n\u003cb data-index-in-node=\"0\" data-path-to-node=\"8,1,0\"\u003eWhy?\u003c\/b\u003e You need to check if the two components (A and B) are coming out evenly from the hoses and mixing correctly in the nozzle. You are ready for injection when you see that the color and consistency are stable.\u003c\/li\u003e\n\n\n\u003c\/ul\u003e\n\u003ch3 data-path-to-node=\"2\"\u003e3. Application and Filling Technique\u003c\/h3\u003e\n\u003cp data-path-to-node=\"3\"\u003ePolyurethane injection application prevents voids by pushing out the air inside as the material advances.\u003c\/p\u003e\n\u003ch3 data-path-to-node=\"4\"\u003eDetermining Hole Spacing\u003c\/h3\u003e\n\u003cul\u003e\n\n\u003cli\u003e\n\n\u003cb data-index-in-node=\"0\" data-path-to-node=\"5,0,0\"\u003eHorizontal and Vertical Spacing:\u003c\/b\u003e Drill holes on the surface you are applying to (wall, boat hull, or panel...) with a spacing of \u003cb data-index-in-node=\"100\" data-path-to-node=\"5,0,0\"\u003e30 cm to 50 cm\u003c\/b\u003e.\u003c\/li\u003e\n\n\u003cli\u003e\n\n\u003cb data-index-in-node=\"0\" data-path-to-node=\"5,1,0\"\u003eHole Diameter:\u003c\/b\u003e Use a drill bit of appropriate diameter (usually 10-12 mm) that allows the nozzle tip to fit snugly and ensure a seal.\u003c\/li\u003e\n\n\u003cli\u003e\n\n\u003cb data-index-in-node=\"0\" data-path-to-node=\"5,2,0\"\u003eAir Vent:\u003c\/b\u003e Always leave a \"vent hole\" at the highest point. This allows air to escape as the material rises.\u003c\/li\u003e\n\n\n\u003c\/ul\u003e\n\u003ch3 data-path-to-node=\"6\"\u003eApplication Order (Bottom-Up Method)\u003c\/h3\u003e\n\u003col\u003e\n\n\u003cli\u003e\n\n\u003cb data-index-in-node=\"0\" data-path-to-node=\"7,0,0\"\u003eStart from the Lowest Point:\u003c\/b\u003e Due to the principle of gravity and expansion, always start the injection from the lowest or outermost hole.\u003c\/li\u003e\n\n\u003cli\u003e\n\n\u003cb data-index-in-node=\"0\" data-path-to-node=\"7,1,0\"\u003eObservation and Transition:\u003c\/b\u003e When the polyurethane foam starts to overflow from an adjacent hole or a hole above in a \u003cb data-index-in-node=\"71\" data-path-to-node=\"7,1,0\"\u003e\"cream-like consistency,\"\u003c\/b\u003e that area is filled.\u003c\/li\u003e\n\n\u003cli\u003e\n\n\u003cb data-index-in-node=\"0\" data-path-to-node=\"7,2,0\"\u003eSealing:\u003c\/b\u003e Temporarily close the overflowing hole with a plug or your finger (wearing gloves) for a short period and immediately move to the next hole to continue injecting.\u003c\/li\u003e\n\n\u003cli\u003e\n\n\u003cb data-index-in-node=\"0\" data-path-to-node=\"7,3,0\"\u003eContinuous Progress:\u003c\/b\u003e Repeat this process until material emerges from the top vent hole.\u003c\/li\u003e\n\n\n\u003c\/ol\u003e","brand":"İzotüp","offers":[{"title":"Default Title","offer_id":45457505583161,"sku":null,"price":8500.0,"currency_code":"TRY","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0772\/0727\/3529\/files\/izotupamazon.jpg?v=1772026315","url":"https:\/\/www.izotup.com\/en\/products\/i%cc%87zotup-200-enjeksiyon-kiti","provider":"İzotüp","version":"1.0","type":"link"}